410 Santa Maria, Irvine, CA 92606
E-mail us: [email protected]
24 Hour Service - 7 Days a Week
Find common Whirlpool error codes for washers, dryers, refrigerators, dishwashers, ovens, and other appliances, with explanations of what each fault may indicate.
Whirlpool appliances use electronic controls and sensors to monitor water filling, draining, temperature, airflow, doors and lids, electrical supply, and communication between components.
Whirlpool appliances use electronic controls and sensors to monitor water filling, draining, temperature, airflow, doors and lids, electrical supply, and communication between components.
An error code is an important diagnostic clue, but it does not necessarily identify one failed part. Whirlpool uses different controls across appliance families and generations, so the full model number and actual symptoms should be considered together.
F5 E2 means the washer cannot lock the door correctly. Clothing or another obstruction near the door can sometimes prevent locking.
F8 E1 or Lo FL means the washer is not detecting the expected incoming water. Check that the water supply is open and inlet hoses are not kinked or restricted.
F9 E1 indicates that draining is taking longer than expected. A restricted drain hose, incorrect installation, or excessive suds can contribute.
F7 E1 concerns motor-speed sensing.
F8 E2 identifies a problem involving the detergent-dispenser system on applicable models.
F3 E1 means the washer cannot correctly detect water level. The appliance control or related wiring may be involved.
F5 E2 indicates that the lid lock cannot engage.
F8 E1 and LF indicate excessive filling time or insufficient detected water flow.
When a washer repeatedly stops during filling, leaves water inside, or cannot lock the lid, the point in the cycle where the error appears helps with diagnosis.
F8E4 means water has been detected in the drip tray. A leak, water connection, or float-switch system may be involved.
F9E1 identifies a long-drain condition. Check the accessible filter, drain hose, sink disposal connection, and air gap where applicable.
F7E2 indicates a wash-motor error.
F6E1 concerns communication between the user interface and main control.
F1E1 can indicate a dishwasher control-module fault.
AF or F4E3 means airflow through the dryer or exhaust system is restricted.
Possible external causes include a loaded lint screen, crushed duct, blocked exterior vent, or an exhaust path with excessive restriction.
Persistent airflow warnings combined with long drying times or excessive heat should not be ignored.
Other F/E combinations can indicate electronic faults that require model-specific diagnosis.
F9 or F9 E0 can indicate incorrect electrical connection or an abnormal voltage condition. It may also appear after certain power disturbances.
F1-E can involve the oven control or associated wiring.
On wall ovens, F6 E4 may indicate a problem involving the Appliance Manager Control or related wiring.
For cooktops, FC E1 can indicate a touch-interface or wiring problem.
F6E4 means communication has been lost between the user interface or keypad and interface control.
Persistent electrical warnings should be properly diagnosed rather than repeatedly cleared.
Built-in microwaves may display F9, F9 E0, or PF for electrical connection, voltage, or power-event conditions.
Because microwaves contain hazardous high-voltage components even after power is disconnected, internal repair should be performed by qualified personnel.
Whirlpool refrigerators can display F-style faults or a flashing F.
On supported models, F3 E1 is one documented example. Whirlpool recommends a power reset as an initial external check, followed by professional diagnosis if the warning returns.
Refrigerator codes vary significantly between product families, so cooling performance and model information are especially important.
Record the complete code before clearing it and note what the appliance was doing when the fault occurred.
External checks involving water supply, accessible hoses, dishwasher filters, or dryer airflow may resolve some conditions.
Persistent electronic, motor, sensor, heating, cooling, or electrical faults require proper testing. Avoid replacing boards, motors, pumps, locks, or sensors based only on an online description.
For professional Whirlpool appliance diagnostics and repair, contact Reliable Hands Appliance.
Phone: +1 (714) 338-9438
Email: [email protected]
Office Hours: Monday through Friday, 7:00 AM to 7:00 PM
Saturday: 9:00 AM to 6:00 PM
Sunday is reserved for emergency calls. Call to confirm availability.
Office: 410 Santa Maria, Irvine, CA 92606
Time Zone: Pacific Time
